Disclaimer: The information provided has been prepared as a guide only additionally, the steps taken will probably vary for many different appliance models. We strongly suggest utilizing a qualified engineer to undertake major repairs and fault finding.
 |
Water Doesn't Flow Easily Into the Coffee Maker
This is among the most common problems that often occur with an electric coffee maker. It's, however, a problem that can be solved without an excessive amount difficulty in many instances.The leading grounds for this type of dilemma are any sort of blockage or water clog. One thing to do is examine the tube within the coffee pot.
You also have to make sure that the machine thermostat and timer are in working order. If these components are fine, there's a chance you're dealing with a pump valve problem. A busted or stuck pump valve could easily block the flow of water through the coffee machine.
This problem might also indicate that the coffee machine heater has malfunctioned and is will no longer operational.
Coffee Brewed From the Machine Doesn't Stay Warm
In case the coffee brewed from the machine does not seem to stay adequately warm, you will have to inspect the heating element of the appliance. Check the Keep Warm switch of the machine for continuity with an electrical tester. Also, make certain that the Auto Shut Off switch is in the proper position while in the brewing process.
The Coffee Maker Seems to be Leaking
In some cases, it might appear as if your coffee maker is leaking warm water or there might be an excess of steam popping out. Quite often, this means that faulty tubing inside the coffee machine. This situation can be easily resolved by making certain the tubes are correctly installed and aren't loose.
The Brew from My Coffee machine Is Getting Weaker
A fairly common complaint would be that the brew made by the coffee machine keeps getting progressively weaker as time passes by. In most cases, this issue is connected to the plate that spreads water above the coffee basket. If it has developed cracks or has broken, it will need to get replaced.
My Coffee Machine Creates a Clicking Noise
Sometimes, a coffee machine will develop a noise during operation. Besides this being annoying, but it surely might also apparently slow down the entire coffee brewing cycle.In case, the coffee machine drips extremely slowly and there's a pronounced sound accompanying it, this could indicate blockages in the machine. Dirt or mineral deposits from your water can block the tubing inside the coffee machine. In these instances, the coffee machine has to be properly cleaned to ensure complete removing any blockages.
This kind of noise is quite common in some coffee machines which are air pressurized. Any dirt or residue that forms inside the coffee machine passages will cause noise and disrupts the brewing process. Although slightly expensive, it may be a more sensible choice to use bottled drinking water with your coffee machine. This could prevent mineral build-ups that create noise.
Noises from your coffee machine are also caused should there be any loose components inside the appliance. Handling the coffee machine roughly may lead to certain parts coming loose or may weaken connections within the machine. Not simply are loose parts prone to cause noise, but they will likely interfere with the coffee making process and extend it. Confirm the various parts of your machine to make sure that they all are tightly fitted.
 |
| Nespresso Zenius Coffee Machine |
If you want to rent a coffee machine and let the supplier carry out scheduled maintenance on coffee machine then you certainly must consider below factor:
1. How many cups every day do you require the machine to be able to cope with?1-20/21-50/51-100/101+
2. Will staff, clients and/or customer help themselves, or will there be someone to make and serve the coffee?
3. What kind of beverages do you want to get from the machines? Just filter? Espresso & black coffee? Cappucino? Hot chocolate?
4. Would you mind powdered milk or prefer fresh milk?
5. Can you plumb the device into a fixed water point or will the device have its own water tank?
Please click the following link to continue reading [ Coffee Machine Rental ] article.
Saeco Coffee Machine Repairs
 |
| Philips Saeco Coffee Machine |
Most common issue about Saeco coffee machine.
- No water from the steam wand. Probably some blockage in either the steam valve and the water is taking the path of least resistance. I'd first try running a small piece of wire up the steam wand to ascertain if it's plugged, otherwise, you are most probably going to have to carry out some disassembly. Is your pump running at all? If you cannot get water from your brew head either then the wand probably isn't your issue.
- The machine won't start. In the event the machine has overheated to the level that it has no power it's either tripped the over-temperature fuse that's clamped to the boiler or it's ruptured the heating element, both of which require opening the machine and replacing parts. If you are curious, the machine comes with a 2-part boiler that can be opened, which is how you replace the heater.
- Why did machine stop making steam? Replace broken heat element, or clean filthy steam tube is likewise possibles fixes.
Delonghi Coffee Machine Repairs
 |
| Delonghi Coffee Machine |
Below is some troubleshooting tips that ought to assist you to repair a DeLonghi coffee machine.
- The device doesn't switch on: examine the power cord and fuses.
- The coffee isn't sufficiently warm: preheat your cups and descale the machine.
- No coffee extraction: clean and descale if required.
- Leakage in capsule area: clean the capsule holder and make sure the capsule is inserted correctly.
- No warm water or steam: clean and descale if required.
- The milk doesn't froth: clean the frothing device. In addition, we recommend using semi-skimmed milk.
- No water flow: fill the tank and ensure it is correctly inserted.
Jura Coffee Machine Repairs
 |
| Jura Coffee Machine |
Jura coffee machine will typically prompt out an error message to indicate an issue with the machine. Listed below some of the most common error messages for Jura Coffee Machine.
• Failure 8 (Most common error message of all Jura machines)
Difficulties with positioning the brewing unit.
Causes / troubleshooting:
- Brewing unit challenging to move because of worn, swollen or broken sealing rings- replace sealing rings or perhaps the entire brewing unit.
- Encoder defective. (count error at the head of the brewing unit or at the drive pinion of the gear motor) An incorrect position of the brewing unit is transmitted to the electronics. - check encoder cable or replace encoder if necessary.
- Brewing unit motor doesn't move ( the machine is clicking instead), the transformer is defective. - replace the transformer.
- Motor or motor mounting defective. (Chattering or very low buzzing) - replace brew group motor.
• Failure 1 - Defect in the steam water heater
Causes / troubleshooting:
- Thermal sensor defective - replace thermal sensor
- Cable to the thermal sensor is broken or contact pins are corroded - replace/repair cable.
- Heating or thermal cut-out are defective - measure and replace parts if needed
- Triac on the power board is defective. The heater heats up until triggering the over temperature protection - replace the overtemperature protection (thermal cut-out) as well as the power board or a single triac.
• Failure 2 - The machine is way too cold
Causes / troubleshooting:
- Thermal sensor defective - replace thermal sensor
- Room temperature is not high enough (<15°C) - keep the device for several hours at room temperature (20°C). (This proceeding is merely necessary if the device was actually located in a freezing surrounding)
• Failure 3 - Sensor problem / fault in the heating circuit
Causes / troubleshooting:
- Thermal sensor defective. (Determine resistance value; at 20°C approx. 12kOhm) - if the value differs clearly, the thermal sensor must be replaced.
- Cable to the thermal sensor is broken or contact pins are corroded - replace/repair cable.
- Control board defective - replace electronics / replace EPROM.
- Heating or thermal cut-out defective - measure and replace parts when necessary.
• Failure 4 - Temperature measuring fault of steam circuit
Causes / troubleshooting:
- Thermal sensor defective. (Determine resistance value. at 20°C approx. 12kOhm) - replace thermal sensor
- Cable to the thermal sensor is broken or contact pins are corroded - replace/repair cable.
- Control board defective - replace electronics / replace EEPROM.
• Failure 5 - Required temperature not reached
Causes / troubleshooting:
- Thermoblock has blown. (resistance value can not be defined/is infinite) - replace thermoblock.
- Thermal cut-out (overtemperature protection) is blown - replace thermal cut-out. (It's recommendable to change the temperature sensor as well to prevent another fault)
- Power electronic is defective (resistance value between the connections cannot be determined, there is no voltage on the connector pins) - replace triacs of the power board or entire power board.
• Failure 6 - Electronic scaling monitor reports an error
Causes / troubleshooting:
- The sensor is above the measuring tolerance -clean the contact pins, dry them and apply contact spray if needed.
